1000 series
1000 SERIES INSULATED STEEL AND GLASS MODULAR WINE DOORS AND VISION LIGHTS
PART 1 – GENERAL
1.01 SUMMARY
A. Furnish insulated steel and glass modular wine doors and vision lights, including frames, glazing, hardware, and accessories.
B. Work includes factory pre-glazed modular framing, insulated door assemblies, and installation hardware.
1.02 REFERENCES
A. ASTM C1048 – Heat-Treated Flat Glass.
B. ANSI Z97.1 – Safety Glazing Materials Used in Buildings.
C. ASTM E1300 – Glass Strength and Load Resistance.
1.03 SUBMITTALS
A. Product data for doors, frames, glazing, and hardware.
B. Shop drawings indicating dimensions, profiles, glazing, and modular connections.
C. Samples of finishes and hardware upon request.
1.04 QUALITY ASSURANCE
A. Manufacturer shall have a minimum of five (5) years’ experience producing insulated steel and glass door systems.
B. All glazing shall comply with applicable safety glazing standards.
1.05 DELIVERY, STORAGE, AND HANDLING
A. Deliver materials in manufacturer’s original, unopened packaging.
B. Store materials in a dry, protected location to prevent damage.
PART 2 – PRODUCTS
2.01 MANUFACTURER
A. Basis of Design: 1000 Series Insulated Steel & Glass Modular Wine Doors and Vision Lights by Wine Front.
B. Substitutions: In accordance with Division 01 requirements.
2.02 DOOR CONSTRUCTION
A. Door Size: As indicated on drawings.
B. Door Construction:
1. 1-1/2″ x 1-1/2″ mechanically fastened, thermally enhanced steel door assembly.
2. Core-filled insulated construction.
3. Fully weathered assembly suitable for temperature-controlled environments.
2.03 FRAMES
A. Four-sided, core-filled, fully weathered steel door frame.
B. Frame depth and profile as required for wall construction and modular system integration.
2.04 MODULAR FRAMING SYSTEM
A. 1″ x 2″ steel modular framing system.
B. Factory pre-glazed units.
C. Installation hardware provided by the manufacturer.
2.05 GLAZING
A. Glass Type:
1. 3/4″ insulated glass unit (IGU).
2. Clear tempered safety glass.
B. Glass shall comply with ASTM C1048 and ANSI Z97.1.
2.06 HARDWARE
A. Standard Hardware:
1. 4-3/4″ barrel hinges.
2. 12″ offset square pull handle.
3. Proprietary magnetic and ball-bearing catch system.
B. Hardware finish: As selected by Architect.
2.07 ACCESSORIES AND OPTIONS
A. 90-degree machined, core-filled corner and wall posts, where indicated.
PART 3 – EXECUTION
3.01 EXAMINATION
A. Verify opening dimensions and conditions prior to installation.
B. Do not proceed with installation until unsatisfactory conditions have been corrected.
3.02 INSTALLATION
A. Install door and modular framing systems in accordance with manufacturer’s written instructions and approved shop drawings.
B. Ensure doors are plumb, level, square, and properly aligned.
C. Provide complete, weathertight installation.
3.03 ADJUSTING AND CLEANING
A. Adjust doors and hardware for smooth operation.
B. Clean glass and exposed surfaces upon completion of installation.
Warranty
Name
Address
Insulated Steel & Glass Modular Door and Partition System
PART 1 – GENERAL
1.01 SUMMARY
A. Furnish and install factory-fabricated insulated steel and glass modular door and partition systems as specified herein.
B. System shall include doors, framing, glazing, hardware, finishes, and accessories required for complete installation.
1.02 REFERENCES
A. ASTM E84 – Surface Burning Characteristics of Building Materials
B. ASTM E1300 – Standard Practice for Determining Load Resistance of Glass
C. ANSI Z97.1 – Safety Glazing Materials Used in Buildings
1.03 SUBMITTALS
A. Product Data: Manufacturer’s technical literature, system descriptions, profiles, finishes, and performance data.
B. Shop Drawings: Fully dimensioned elevations, sections, details, anchorage methods, hardware locations, and tolerances.
C. Samples: Powder coat finish samples, minimum 3″ x 3″.
D. Warranty Documentation.
1.04 QUALITY ASSURANCE
A. Manufacturer shall have minimum five (5) years’ experience producing thermally enhanced steel and glass door and partition systems.
B. Fabrication shall be performed in a controlled factory environment.
1.05 DELIVERY, STORAGE, AND HANDLING
A. Deliver materials in manufacturer’s original packaging, labeled and protected.
B. Store products in a clean, dry, covered location.
PART 2 – PRODUCTS
2.01 MANUFACTURER
A. Basis of Design: Wine Front Direct
B. Approved Substitutions: Subject to architect approval.
2.02 DOOR SYSTEM
A. Door Construction:
1. Profile: 1-1/2″ x 1-1/2″ thermally enhanced steel stiles and rails.
2. Fabrication: Fully welded and ground smooth.
3. Glazing: 3/4″ insulated glass units.
4. Hardware: Premium Adams Rite® hardware set including closers, latches, and pull handles as scheduled.
5. Finish: Factory-applied architectural-grade powder coat.
2.03 PARTITION FRAMING SYSTEM
A. Framing Construction:
1. Profile: 1-1/2″ x 1-1/2″ thermally enhanced / thermally broken steel framing.
2. Fabrication: Fully welded construction with concealed anchorage.
3. Glazing: 3/4″ tempered insulated glass.
4. Finish: Factory-applied architectural-grade powder coat.
2.04 GLAZING
A. Type: Insulated Glass Units (IGU)
B. Thickness: 3/4″ nominal
C. Safety Compliance: ASTM E1300 and ANSI Z97.1
D. Performance: Designed for controlled wine cellar environments
2.05 HARDWARE
A. Manufacturer: Adams Rite®
B. Finish: Coordinated to powder coat finish
C. Components: Closers, latch sets, locks, pull handles, and accessories as scheduled
2.06 FINISHES
A. Powder Coat:
1. Architectural-grade polyester powder coat.
2. Applied in a controlled factory environment.
3. Minimum thickness per AAMA standards.
PART 3 – EXECUTION
3.01 EXAMINATION
A. Verify opening dimensions, substrate conditions, and tolerances prior to fabrication.
3.02 INSTALLATION
A. Install systems plumb, level, and square in accordance with approved shop drawings and manufacturer’s instructions.
B. Provide complete perimeter sealing and anchorage.
3.03 ADJUSTING AND CLEANING
A. Adjust doors and hardware for proper operation.
B. Clean glass and exposed surfaces.
PART 4 – WARRANTY
4.01 WARRANTY COVERAGE
A. Insulated Glass: Five (5) year limited warranty against seal failure and manufacturing defects.
B. Powder Coat Finish: Ten (10) year limited warranty against fading and normal wear.
C. Framing and Door Construction: Lifetime warranty against structural frame failure.